Temperaturen Zyl. / Ansaugluft

Moderatoren: Andi, Krieger

Antworten
Benutzeravatar
jäger
Warrior
Beiträge: 286
Registriert: Freitag 1. August 2014, 17:15
Hat sich bedankt: 0
Danksagung erhalten: 0
Kontaktdaten:
Germany

Temperaturen Zyl. / Ansaugluft

Beitrag von jäger »

Guten Morgen liebe Leute,

habe bei den Amis den folgenden Beitrag gefunden. Soweit ich verstanden habe hat einer die Ansauglufttemp. bzw. die einzelnen Zylinder gemessen. Finde den Beitrag interessant aber so richtig habe ich das nicht 100% verstanden. Fr. Google wirft alles durcheinander aus :lol: Die angegebene Temperaturen, sind das Kelvin gemeint oder doch Grad ? besser gefragt, ist einer so freundlich und kann mir hier etwas helfen ?

Den Beitrag habe ich hier rein kopiert.
Danke schon mal im voraus.


http://www.rswarrior.com/forums/13-tech ... -03-a.html



After several discussions on intake air temperatures I decided to step up to the plate & run a test.

Intake air temperature test 10-26-03.

Ambient temperature @ 4PM EST from weather.com, Naples, FL.

86 degrees, 55% humidity

Everything I shot with my digital pyrometer that was in the shade all day had a reading of 88 to 91 degrees but I will call the 86 degree reading baseline.

Note: Found the specs on the pyrometer, accuracy + or - 2% at 70 degrees.

IMPORTANT--I do not have an air scoop or anything else on the right side of my bike to collect or direct air to the under tank area. I also run a Davern Machine oil cooler so my oil temp may be lower than other Warriors that check their oil temps with the computer. I have also deactivated the LCV so the engine will not ingest air because the oil temp is not high enough.

First test was to take the bike on a 10.5 mile run. Speed varied to 60 mph but I ran it to the limiter in 2nd & 3rd gear about 8 miles into the run. The last 1/8th mile was in first gear getting into a safe area to park.

Taking readings With a digital pyrometer.

Velocity stack facing forward feeding the rear cylinder: 104 degrees
Velocity stack facing the rear & feeding the front cylinder 106 degrees

Front rocker box on left side 112 degrees
Rear rocker box on left side 108 degrees

With the motor off for two minutes I went into the computer to read the temps there.

Code 5, intake air temp sender, 117 degrees
Code 10, oil temperature, 162 degrees
Code 11, Engine temp (cylinder) 208 degrees.

The bike was started & allowed to idle in place for 2 minutes turned off & all the readings were taken again.

Forward facing V Stack, 110 degrees
Rear facing V Stack, 121 degrees

Front rocker box, 105
Rear rocker box, 104

Ambient sensor, 117
Oil temp, 167
Cylinder temp, 228

I restarted & ran the bike for 2.6 miles at 50 mph, shut it off & immediately shot the velocity stacks with the pyrometer. ( no particular reason why I went 2.6 miles it was just a convenient place to pull off the road)

Forward facing V stack, 95 degrees
Rear facing V Stack, 97 degrees

Front rocker box, 103
Rear rocker box, 104

ambient sensor, 120
Oil temp, 172
Cylinder temp, 223

I then shot the cylinders under the heads, Rear cylinder 217, Front cylinder 219.

I was slightly surprised to find the rear cylinder slightly cooler than the front & have surmised 2 reasons for this.

First, The forward facing Velocity stack has its filter in fresh air near the front of the bike. If you look at all the temperatures you will find the forward facing stack is cooler in all tests. The forward facing V stack feeds the rear cylinder.

Second. I have modified the left side scoop so it is tucked tightly against the rear cylinder. I did this mod so I could squeeze the tank with my left knee, apparently it helps keep the rear cylinder cool as well.

My two Conclusion from this test:

First: When your bike is moving down the road there is not enough temperature difference between ambient air temperature & the air temperature that the engine is swallowing to give much more thought to.

Second: I need to finish my right side air scoop so my rear facing V Stack can run 2 degrees cooler & be equal to the other one.

This concludes the intake air temperature test
__________________
Forum member #113
Benutzeravatar
xv-manni
Warrior (1)
Warrior (1)
Beiträge: 132
Registriert: Dienstag 9. September 2014, 21:55
Wohnort: Arnsberg
Hat sich bedankt: 0
Danksagung erhalten: 0
Kontaktdaten:
Germany

Re: Temperaturen Zyl. / Ansaugluft

Beitrag von xv-manni »

Wenn das Kelvin wären, wär du Luft wohl etwas zu kalt, um noch Mopped zu fahren!!! :lol:
Amis messen in Fahrenheit. ;-)
http://www.celsius-fahrenheit.de/
--
Gepustet von meinem Windoof-Fön
(c) Mikrodoof 2tausendirgendwas
Benutzeravatar
jäger
Warrior
Beiträge: 286
Registriert: Freitag 1. August 2014, 17:15
Hat sich bedankt: 0
Danksagung erhalten: 0
Kontaktdaten:
Germany

Re: Temperaturen Zyl. / Ansaugluft

Beitrag von jäger »

jow danke,

Zurück zu „Technik Forum“

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 3 Gäste